News

The Advantages of the Pneumatic Drilling compare to Water Drilling

January 04 , 2022

The Advantages of the Pneumatic Drilling compare to Water Drilling 1) The single impact power of a pneumatic drill is large, generally up to tens of kilograms or more than a hundred kilograms, which is more than ten times-dozens of times the single impact energy of the current hydraulic impactor. Therefore, from the perspective of rock crushing, the gas drill is mainly based on impact crushing rock, and the rotation only changes the location of impact crushed rock, and at the same time plays the role of auxiliary rock crushing. Therefore, the drilling efficiency depends to a large extent on the performance and quality of the down-the-hole hammer. (2) Due to the low air density during gas drilling, the pressure of the gas column in the full-hole section is much smaller than that of the liquid column, which improves the multi-directional pressure state of the rock at the bottom of the hole, which is conducive to breaking the rock and improving the drilling efficiency; But on the other hand, it requires a high flow rate to purge the bottom of the hole. Generally, it is required that the speed of the upward return air in the outer annular gap of the drill pipe must be 10-15m/s, and the hydraulic impactor of the water drill has a liquid flow when drilling. The up-return speed is only 0.8-1.2m/s, and the annulus flow velocity during small-diameter diamond rotary drilling is mostly 1m/s. Therefore, when drilling with a pneumatic DTH water well drilling rig, there is less rock powder at the bottom of the hole, which reduces repeated fragmentation of rock powder, and its drilling efficiency can be doubled. (3) The down-the-hole hammer of the air drill uses compressed air as the motive medium when drilling. After the high-pressure air passes through the impactor, the pressure around the bit is suddenly reduced, and heat is absorbed, which is very beneficial to increase the life of the bit.

Learn More >

Features of crawler water well drilling rig

January 04 , 2022

Features of crawler water well drilling rig Water Well Drilling Rig uses mechanical method to drill holes into the ground. According to the rock breaking method and the type of drilling tool, it can be divided into drilling technology and rotary drilling technology.

Learn More >

Introduction of water well drilling rig crawler

December 28 , 2021

Introduction of water well drilling rig crawler  The crawler water well drilling rig is composed of a crawler track and water well drilling rig, The advanced technology prevent the track from falling off when the water well drill is turning. To improve the firmness of the crawler track and the adhesion between the crawler track and the ground, there are also supporting wheels, supporting wheels, driving wheels and rail links on the water well drilling rig site.  When cleaning the drilling rig, the sludge on the lower walking body should be cleaned at the same time. After the operation, the operator should clean the sludge on the lower walking body while cleaning the cab, if there is sludge attached to the lower walking body. It is impossible to check the related parts. Therefore, please remove these sludge and inspect and maintain the lower walking body 

Learn More >

How to Maintain the water well drilling rig during the run-in period

December 21 , 2021

How to Maintain the water well drilling rig during the run-in period. 1. Pay attention to the working load during the running-in period. Generally, the working load during the running-in period should not exceed 80% of the rated working load, and a suitable workload should be arranged to prevent the occurrence of overheating caused by long-term continuous operation of the machine. 2. Keep the machine clean, adjust and tighten loose parts in time to prevent the loose parts from aggravating the wear of the parts or causing the parts to be lost. 3. Pay attention to frequently check the lubricating oil, hydraulic oil, coolant, brake fluid and fuel oil (water) level and quality, and pay attention to check the seal of the whole machine. It is found that there is too much oil and water during the inspection, and the reason should be analyzed. At the same time, the lubrication of each lubrication point should be strengthened. It is recommended to add grease to the lubrication point during the running-in period (except for special requirements). 4. Pay attention to frequently observe the instructions of each instrument. If there is an abnormality, stop and remove it in time. If the cause is not found and the fault is not removed, the operation should be stopped. 5. At the end of the running-in period, the machine should be subject to mandatory maintenance, inspection and adjustment should be done, and attention should be paid to the replacement of oil. The requirements for use and maintenance of water well drilling rigs during the running-in period can be summarized as: reducing load, paying attention to inspection, and strengthening lubrication. As long as you pay attention to and implement the maintenance and maintenance of the construction machinery during the running-in period as required, it will reduce the occurrence of early failures, prolong the service life, improve operating efficiency, and bring you more economic benefits.

Learn More >

What is a water well driller?

December 20 , 2021

What is a water well driller? A water well driller is a person who operate a mobile drilling rig to drill and monitor groundwater wells for residential, commercial, industrial, and agricultural uses, most often when there is no readily available surface water. The types of drilling methods are rotary, DHT hammer. If the ground is especially hard, you may need to use DTH hammer. After you drill the well in the earth, your duties include installing a pump, sterilizing the system to prevent bacterial growth, and starting the water flow. In some more extensive operations, you manage a small crew of workers. You keep records of each well, and in most states, you provide the government with copies of these records.

Learn More >

Water well drilling rig machine Engine starter usage and maintaining

December 13 , 2021

Water well drilling rig machine Engine starter usage and maintaining The starter is generally composed of three parts: a DC motor, a transmission mechanism and an electromagnetic operating mechanism. The correct use and maintenance methods of the starter, in order to extend the life of the starter, and ensure that it can work quickly, reliably, and safely, the correct use and maintenance requirements for the starter of the water well drilling rig are as follows

Learn More >